Vælg din model

I tvivl om model?
Er du i tvivl om hvilken model du har har vi lavet en lille guide så du kan finde kendetegnene ved din model.

iPhone 3G klik her
iPhone 3GS klik her
iPhone 4 klik her iPhone 4S klik her

Du er her: Shop

Headphone jack kabel - klasse B

Produktbeskrivelse

Headphone Jack kabel til iPhone 4S.

Kablet kan afhjælpe, hvis du har problemer med:
- jackstikket (der hvor du tilslutter høretelefoner)
- volume op/ned-knappen
- mute-knappen

Husk reparations kit til din reparation.

__________________________________________________

Klasse A vs. klasse B:

Klasse A kommer meget tæt på de originale dele. Det vil sige, at delen lever helt op til den originale del. Dette produkt er til den kræsne bruger, der ønsker sin reservedel udskiftet med den bedste reservedel, der pt. er på markedet. Konkret er alle elektronik-, plast- og glasdele af langt større kvalitet end B produkter.

Klasse B indeholder kopi reservedele, der ikke lever helt op til de originale dele. Klasse B produktet er dog ikke et dårligt produkt, men et produkt til den ikke så kræsne bruger, der godt kan leve med det næst-bedste. Reservedelene har en større fejlprocent og har ikke samme kvalitet i elektronik-, glas- og plastikdele som i A produkterne.

Headphone jack kabel - klasse B

79 DKK

Varen er på lager
Levering 1-2 hverdage

Dette produkt passer til følgende modeller:
iPhone 4S

Farve: Sort

Antal stk.

Vi modtager:

Leveringstid - 1-2 hverdage. Varen er på lager
Returret - 30 dage, du kan altid få pengene tilbage
Sikkerhed - vi er e-mærket
Hjælp og support - tlf og email hverdage 09-16
Fast fragt - kun 25 DKK uanset størrelse

Der er en guide til brug af dette produkt. Klik her for at åbne guide

Guide til Headphone jack kabel - klasse B

Trin 1

Before disassembling your iPhone, be sure it is powered off.
Remove the two 3.6 mm Pentalobe screws next to the dock connector.
During reassembly, we recommend you replace the 5-point screws with equivalent Phillips screws. Our Liberation Kit provides the tools and screws needed to replace the Pentalobe screws with Phillips screws.
The 5-Point Screwdriver should only be used once, as it has the potential to strip the screws.

Trin 2

Push the rear panel toward the top edge of the iPhone.
The panel will move about 2 mm.

Trin 3

Pull the rear panel away from the back of the iPhone, being careful not to damage the plastic clips attached to the rear panel.
Remove the rear panel from the iPhone.

Trin 4

Remove the following screws securing the battery connector to the logic board:

Take care of remove for screw

Trin 5

Use a pair of tweezers to remove the pressure contact near the battery connector.
When reinstalling the pressure contact, be sure to clean it with a degreaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to create wireless interference.

Trin 6

Use the edge of a plastic opening tool to gently pry the battery connector up from its socket on the logic board.

Trin 7

Insert the edge of a plastic opening tool between the battery and the outer case near the bottom left corner of the iPhone.
Run the plastic opening tool along the right edge of the battery and pry up at several points to completely separate it from the adhesive securing it to the outer case.

Trin 8

Use the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone.
Remove the battery.

Trin 9

Remove the following screws securing the dock connector cable cover to the logic board:

One 1.5 mm Phillips screw

One 1.2 mm Phillips screw

Remove the metal dock connector cable cover.

Trin 10

Use the edge of a plastic opening tool to pry the dock cable up from its socket on the logic board.

Trin 11

Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.

Trin 12

Use the edge of a plastic opening tool to pry the Wi-Fi antenna cable up from its socket on the logic board.
De-route the Wi-Fi antenna cable out from under the metal fingers attached to the logic board.

Trin 13

If necessary, use a pair of tweezers to remove the outer plastic ring located on top of the rear camera's flash assembly.

Trin 14

Remove the following four screws securing the cable cover to the logic board:

One 2.7 mm Phillips screw

One 2.6 mm Phillips screw

One 1.3 mm Phillips screw

One 1.2 mm Phillips screw

Trin 15

Use the edge of a plastic opening tool to pry the cable cover tabs out of their slots cut into the EMI shield on the logic board.
Lift the cable cover from its edge nearest the top and remove it from the iPhone.

Trin 16

Use the edge of a plastic opening tool to pry the rear camera connector up from its socket on the logic board.
Be careful not to break any components off the surrounding area on the logic board as you pry upwards.
Remove the rear camera from the iPhone.

Trin 17

Use a SIM card eject tool or a paperclip to eject the SIM card and its holder.
This may require a significant amount of force.
Remove the SIM card and its holder.

Trin 18

Remove the five cables near the top of the logic board in the following order:

Headphone jack/volume button cable

Front facing camera cable

Digitizer cable

Display data cable

Power button cable (located underneath the headphone jack/volume button cable as shown in the second picture.)

To disconnect the cables, use the edge of a plastic opening tool to gently lift their connectors up and out of the sockets on the logic board.
Be careful not to break any of the small and delicate surface mount components as you disconnect the cables.

Trin 19

Remove the 1.5 mm Phillips screw securing the grounding clip to the logic board near the headphone jack.

Trin 20

Lift the small grounding clip up off the logic board and remove it from the iPhone.

Trin 21

Use a small flathead screwdriver to remove the 4.8 mm standoff near the headphone jack.

Trin 22

Use the edge of a plastic opening tool to disconnect the wi-fi antenna from the logic board.

Trin 23

If present, peel the piece of black tape covering the hidden screw near the power button.
Remove the 1.6 mm Phillips screw securing the logic board near the power button.

Trin 24

Remove the following screws securing the logic board to the case:

One 2.5 mm Phillips screw near the vibrator motor

One 2.4 mm Phillips screw

One 3.6 mm standoff along the side of the logic board nearest the battery opening.

Use a small flathead screwdriver to remove the single 3.6 mm standoff.

Trin 25

Carefully lift the logic board from the end closest to the speaker enclosure and slide it away from the top edge of the iPhone.
Remove the logic board.
Before reassembly, be sure to clean all metal-to-metal contact points on the logic board (not the mating halves of connectors) with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause grounding issues.

Trin 26

Be sure not to lose the small grounding finger for the rear facing camera near the power button.

Trin 27

Use the edge of a plastic opening tool to carefully pry the metal front facing camera retainer away from the case of your iPhone.
Remove the front facing camera retainer.

Trin 28

Remove the front facing camera.

Trin 29

Remove the 2.4 mm Phillips screw next to the headphone jack.

Trin 30

Use the edge of a plastic opening tool to peel the upper antenna off the headphone jack.
Use a pair of tweezers to remove the upper antenna from the iPhone.
Before reassembly, be sure to clean the metal-to-metal contact point on the upper antenna (not the mating halves of its connector) with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause wireless interference issues.

Trin 31

Use the edge of a plastic opening tool to dislodge the headphone jack off from its recess in the outer case.
Use the edge of a plastic opening tool to peel the top microphone away from the outer case.
Pull the body of the headphone jack away from the top edge of the iPhone.

Trin 32

Remove the 1.6 mm Phillips screw securing the upper antenna to the outer case.

Trin 33

Remove the four 1.5 mm Phillips screws securing the volume button and silent switch brackets to the outer case.

Trin 34

Use a pair of tweezers to gently pull the silent switch bracket away from the outer case.

Trin 35

Carefully peel the headphone jack/volume button cables off the adhesive securing them to the rear case.
Remove the headphone jack cable assembly from the iPhone.

Trin 36

If you are replacing the headphone jack cable, use the edge of a plastic opening tool to remove the steel brackets for the volume buttons and the silent switch.
Transfer these steel brackets to the new headphone jack cable.

Trin 37

If you are replacing the headphone jack cable, use the edge of a plastic opening tool to remove the steel brackets for the volume buttons and the silent switch.
Transfer these steel brackets to the new headphone jack cable.

Vælg din model

Produktbeskrivelse

Headphone jack kabel - klasse B

79 DKK

Vi modtager:

Guide til Headphone jack kabel - klasse B

Trin 1

Trin 2

Trin 3

Trin 4

Trin 5

Trin 6

Trin 7

Trin 8

Trin 9

Trin 10

Trin 11

Trin 12

Trin 13

Trin 14

Trin 15

Trin 16

Trin 17

Trin 18

Trin 19

Trin 20

Trin 21

Trin 22

Trin 23

Trin 24

Trin 25

Trin 26

Trin 27

Trin 28

Trin 29

Trin 30

Trin 31

Trin 32

Trin 33

Trin 34

Trin 35

Trin 36

Trin 37

PhoneTech.dk

Phonetech.dk ejes og drives af PhoneGadget ApS