Vælg din model

I tvivl om model?
Er du i tvivl om hvilken model du har har vi lavet en lille guide så du kan finde kendetegnene ved din model.

iPhone 3G klik her
iPhone 3GS klik her
iPhone 4 klik her
iPhone 4S klik her
iPhone 5 klik her

Du er her: Shop

iPhone 4

Light Sensor flex kabel

Produktbeskrivelse

Light Sensor flex kabel til iPhone 4.

Kablet kan afhjælpe, hvis du har problemer med:
- lys sensoren i din skærm
- power/sleep knappen

Husk reparations kit til din reparation.

Light Sensor flex kabel

79 DKK

Varen er på lager
Levering 1-2 hverdage

Dette produkt passer til følgende modeller:
iPhone 4

Farve: Sort

Antal stk.

Vi modtager:

Leveringstid - 1-2 hverdage. Varen er på lager
Returret - 30 dage, du kan altid få pengene tilbage
Sikkerhed - vi er e-mærket
Hjælp og support - tlf og email hverdage 09-16
Fast fragt - kun 25 DKK uanset størrelse

Der er en guide til brug af dette produkt. Klik her for at åbne guide

Guide til Light Sensor flex kabel

Trin 1

Before disassembling your iPhone, be sure it is powered off.
Remove the two 3.6 mm Phillips screws next to the dock connector.
Apple has recently substituted the two Phillips screws with 5-Point "Pentalobe" screws. If your iPhone 4 has 5-Point "Pentalobe" screws instead of Phillips, please refer to the second picture.
Remove the two 3.6 mm Pentalobe screws next to the dock connector.
During reassembly, we recommend you replace the 5-point screws with equivalent Phillips screws. Our Liberation Kit provides the tools and screws needed to replace the Pentalobe screws with Phillips screws.
The 5-Point Screwdriver should only be used once, as it has the potential to strip the screws.

Trin 2

Push the rear panel toward the top edge of the iPhone.
The panel will move about 2 mm.

Trin 3

Lift the rear panel away from the iPhone.

Trin 4

Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.

Trin 5

Use an iPod opening tool to carefully pry the battery connector up from the ends closest to the top and bottom edges of the iPhone.
Do not pry against the contact clip.
Remove the contact clip from the iPhone.

Trin 6

Use the clear plastic pull tab to gently lift the battery out of the iPhone.
Be careful when removing the battery with the plastic pull tab. On some units, Apple uses an excessive amount of glue, making it virtually impossible to remove the battery in this fashion (with the tab possibly tearing due to excessive force).
For batteries that "stick", you could use the iPod opening tool to assist (take extra care whilst doing so).
Remove the battery.
Before reconnecting the battery connector, be sure the pressure contact (shown in red) is properly positioned next to the battery connector.
Before reassembly, be sure to clean all metal-to-metal contact points on the pressure contact as well as its contact point on the rear panel with a de-greaser such as windex. The oils on your fingers have the potential to cause wireless interference issues.

Trin 7

Use a SIM card eject tool or a paperclip to eject the SIM card and its holder.
This may require a significant amount of force.
Remove the SIM card and its holder.

Trin 8

Remove the following two screws:

One 1.2 mm Phillips

One 1.6 mm Phillips

Remove the thin steel dock connector cable cover from the iPhone.
Before reassembly, be sure to clean all metal-to-metal contact points on the dock connector cable cover with a de-greaser such as windex. The oils on your fingers have the potential to cause wireless interference issues.

Trin 9

Use an iPod opening tool to gently pry the dock cable connector up off the logic board from both short ends of the connector.

Trin 10

Carefully peel the dock ribbon cable off the logic board and the lower speaker enclosure.

Trin 11

Use an iPod opening tool to pry the lower antenna connector up off its socket on the logic board.
Make sure you don't damage the blue inductor while prying the antenna connector. If you end up having no service message, double check that the blue inductor is still there and soldered properly

Trin 12

Remove the 1.9 mm Phillips screw securing the bottom of the logic board to the inner case.

Trin 13

Remove the following five screws securing the connector cover to to the logic board:

One 2.3 mm Phillips

Two 1.6 mm Phillips

One 1.4 mm Phillips

One 4.8 mm Phillips

When re-assembling, start off with replacing the 4.8 mm Philips screw first, then the 2.3 mm. This is to ensure there is no mix-up, and avoid rendering the LCD and digitizer useless.

Trin 14

Use an iPod opening tool to slightly lift the top edge of the connector cover away from the logic board.
Use the tip of a spudger to pull the connector cover retaining clips away from the inner frame.
Remove the connector cover from the iPhone. Make sure you don't lose the metal clips on the top of the cover where the 4.8mm screw attaches. That's the primary reason for abnormal Wi-Fi performance after the reassembly.
Before reassembly, be sure to clean all metal-to-metal contact points on the connector cover with a de-greaser such as Windex. The oils on your fingers have the potential to cause wireless interference issues. Do not clean the connectors themselves with Windex.

Trin 15

Use an iPod opening tool to carefully lift the rear camera connector up off its socket on the logic board.
Remove the rear camera.

Trin 16

Remove the small circular white sticker (warranty sticker and water indicator) covering the screw near the battery pull tab.
Remove the 2.4 mm Phillips screw that was hidden underneath the sticker.

Trin 17

Disconnect the following connectors from the top of the logic board:

Digitizer cable (From Bottom)

LCD cable (From Bottom)

Headphone jack/volume button cable (From Top)

Top Microphone/sleep button cable (From Top)

Front camera cable (From Top)

It is helpful to use the edge of an iPod opening tool to gently lift the connectors up and out of their sockets on the logic board.

Trin 18

Use a small flathead screwdriver to remove the 4.8 mm standoff near the headphone jack.

Trin 19

Carefully remove the logic board from the iPhone, minding any cables that may get caught.
Note that there is a rubber guard on the edge of the logic board where the Digitizer and LCD ribbon cables bend over the logic board. Make certain it is there before replacing the logic board during reassembly.

Trin 20

Remove the following two screws securing the vibrator to the inner frame:

One 6 mm Phillips

One 1.4 mm Phillips

Remove the vibrator from the inner case.

Trin 21

Use the edge of a plastic opening tool to pry the earpiece speaker away from the adhesive securing it to the front panel.

Trin 22

Remove the two 1.5 mm Phillips screws securing the power button to the outer case.

Trin 23

Carefully pull the power button bracket up and out of the outer case.
This bracket is made of cast aluminum and is very easily cracked. Proceed with caution.

Trin 24

Use a pair of tweezers to pull the body of the headphone jack out of the outer case.

Trin 25

Grab the power & sensor cable near the microphone and peel it off the front panel, being careful not to rip it in the process.

Trin 26

Remove the power & sensor cable from the iPhone 4.

Trin 27

Remove the power & sensor cable from the iPhone 4.

Vælg din model

Produktbeskrivelse

Light Sensor flex kabel

79 DKK

Vi modtager:

Guide til Light Sensor flex kabel

Trin 1

Trin 2

Trin 3

Trin 4

Trin 5

Trin 6

Trin 7

Trin 8

Trin 9

Trin 10

Trin 11

Trin 12

Trin 13

Trin 14

Trin 15

Trin 16

Trin 17

Trin 18

Trin 19

Trin 20

Trin 21

Trin 22

Trin 23

Trin 24

Trin 25

Trin 26

Trin 27

PhoneTech.dk

Phonetech.dk ejes og drives af PhoneGadget ApS